Cylinder Filter with or without Top Flange

Many woven filter cylinders with metal top or flange and rubber or plastic stuck to the cylinder.
Filter cylinders with rubber or plastic stuck to the cylinder.
  • 304 stainless wire mesh cylinders, O.D.: 3/4 - 1" and long 6".
  • 20 mesh screen strainer filter cylinder, size 2" × 4", open at both ends.
  • Cylinder filter, 5 micron stainless steel screen filter, 13 mm ID × 610 mm long.
  • Stainless steel cylinder filter with 3" clamp, material: 316 SS, cylinder size: 56 mm diameter × 310 mm length, 40 mesh.
  • Bucket filter, length 24 inches and diameter 8 inches with mesh grade of 400 or up to 60 microns.
  • Bucket filter, length 24 inches and diameter 8 inches with mesh grade of 250 or up to 80 microns.
  • Cylinder filter, material: stainless steel, 100 mesh outer screen, size: 1.65" × 4-1/4".
  • Cartridge filters 50 microns, to be used before a coalescer to pretreat 400 m3/hr of oily water with 16,000 ppm of oil (sg=0.67).
  • Cylinder-shaped pleated filter, dimensions: ID: 0.25" nominal, OD: 0.65" nominal, 5.5" long
  • Stainless steel filter cartridge, 304 or 316 stainless steel, sizes 40" long, micron rating 5.
  • 2 inch high flat bottom wire mesh filter with lockable lid.
  • Perforated stainless steel filter with 120 and 70 micron is formed into a 36" tube and 21" long for a pollen collector.
  • Mesh filter tubes with mesh counts 200 × 600 mesh, mesh size: 0.0024", material: SS 304, diameters: 3/16".
  • Filter cartridges, 316 stainless steel, 200 micron rating, cartridges are 895 mm long × 225 mm outside diameter.
  • 316 stainless steel cylinder element of 70 micron, 35 micron, 10 micron, and 1 micron; size 7" × 28".
  • 316 stainless steel filter cartridges for a plant with size 1500 mm long and 200 mm wide with a center orifice of 40 mm.
  • Stainless metal mesh filters in the 5 to 20 micron range replacing a standard 10" water filter cartridge.
  • Perforated stainless steel tube filter, dimensions: 8 cm diameter and 18 cm height.
  • Filter cartridges, 316 stainless steel, 200 micron rating, cartridges size: 895 mm long × 225 mm outside diameter.
  • Cylinder filter, size: 23-1/2" round bottom and 10" tall.
  • Metal mesh tubing, dimensions: 4 - 8 inches in width and 10 inches in length.
  • Filter tubes with 1 cm diameter and 1.25 cm length, mesh size 5 um or less, for holding micron sized particles and placed in a flow cell at low flow rate.
  • Stainless steel filter cartridge, 10", 20", 30", 40" long, 0.5, 1, 5, 10, 20, 50 micron rating, 64 mm outside diameter, 28 mm inside diameter, element surfaces plain cylindrical.
A weaving pattern stainless steel cylinder filter with twisted top on.
Stainless steel cylinder filter with twisted top on.
A weaving pattern stainless steel cylinder filter with a twisted top beside.
Stainless steel cylinder filter with twisted top off.
A woven stainless steel cylinder filter with one open end.
Cylinder filter with one open end.
A woven stainless steel cylinder filter with one closed end.
Cylinder filter with one closed end.
  • Round hole cylinder strainer.
    • Material: stainless steel.
    • Hole diameter: 6 mm.
    • Hole distance: 10 mm.
    • Cylinder diameter: 85 mm.
    • Cylinder height: 130 mm.
  • Round hole cylinder strainer.
    • Material: stainless steel.
    • Hole diameter: 6 mm.
    • Hole distance: 10 mm.
    • Cylinder diameter: 85 mm.
    • Cylinder height: 130 mm.
  • Round hole cylinder strainer.
    • Material: stainless steel.
    • Hole diameter: 6 mm.
    • Hole distance: 15 mm.
    • Cylinder diameter: 105 mm.
    • Cylinder height: 180 mm.
  • Round hole cylinder strainer.
    • Material: stainless steel.
    • Hole diameter: 8 mm.
    • Hole distance: 16.5 mm.
    • Cylinder diameter: 135 mm.
    • Cylinder height: 200 mm.
  • Cylinder filter mesh.
    • Cylinder size: ID 50 mm, L 232 mm, thickness 0.5 mm.
    • Material: galvanized.
    • Mesh number: 30 or 100.
  • Cylinder filter.
    • Material: 316L.
    • Crimped wire mesh: diameter 1 mm.
    • Mesh size 10 × 10 mm.
    • Height of cylinder: 1600 mm.
    • Cylinder diameter: 40 mm or 60 mm.
    • Bottom type: flat plate bottom or left part open bottom.
  • Cylinder filter element.
    • Material: SS 316L.
    • Thickness: 0.039".
    • Outside diameter: 3".
    • Round hole with hole size: 0.1563".
    • Hole centers: 0.1875"
    • Total height of filter: 13" including a safe margin of 0.5".
  • Cylinder filter.
    • Material: SS 304.
    • Wire diameter: 0.23 mm.
    • Cylinder size: 120 mm inside diameter and 645 mm length.
    • Mesh size: 50 × 50 mesh.
    • Weave type: plain weave.
    • Process treatment: welded with silver powder.
  • Cylinder filter.
    • Material: SS 304.
    • Wire diameter: 0.18 mm.
    • Cylinder size: 120 mm inside diameter and 645 mm length.
    • Mesh size: 60 × 60 mesh.
    • Weave type: plain weave.
    • Process treatment: welded with silver powder.
  • Cylinder filter.
    • Material: stainless steel.
    • Filtration: 5 micron.
    • Cylinder size: 13 mm ID × 610 mm long.
    • Mesh counts: 325 or 2300 mesh.

Inquiry for Our Product

Boegger Industrial Limited
Email: info@wiremeshfilter.org

When you contact us, please provide your detail requirements. That will help us give you a valid quotation.

Full Name *
Country Code * + Phone Number *
Message *